Countrywide delivery within 24–48 hrs — order before 3PM for same-day dispatch

Shop Hot Deals → +254 728 163329

HDPE end cap

Sale!

HDPE end cap

Price range: KSh100 through KSh550

Threadless HDPE compression end cap, PN16 to PN25, in six sizes (20-63 mm). Grips HDPE or PPR pipe without threads or glue. Sale prices KSh 100-550. Countrywide delivery; bulk by quote.

SKU: N/A Categories: ,

Delivery & Returns

Countrywide Delivery Fast, reliable shipping to any part of Kenya. Shipped within 24-48 hours.
Warranty & Returns Genuine product warranty & easy return policy on manufacturer defects.
Need Help Ordering? Call / WhatsApp support: +254 728 163329

Description

HDPE end cap

An HDPE end cap is a compression fitting that seals the open end of an HDPE pipe. It grips the pipe wall without threads or glue, so the line stays closed under pressure. Eunidrip Irrigation Systems stocks it in six sizes, 20 mm up to 63 mm, for drip, sprinkler and domestic water lines.

Because the fitting is threadless, it suits both HDPE and PPR pipe. It is moulded from tough polymer that resists corrosion, therefore the water stays clean. See our HDPE pipe listing for the pipe it closes.

 

HDPE End Cap Sizes and Prices in Kenya

We stock six compression sizes. Each matches a nominal pipe outside diameter. The table lists regular and current sale prices per fitting.

Pipe size Outside diameter Regular price (KSh) Sale price (KSh)
½” 20 mm 120 100
¾” 25 mm 150 130
1″ 32 mm 220 200
1¼” 40 mm 300 250
1½” 50 mm 400 350
2″ 63 mm 650 550

Prices are per fitting and include the sale discount. Bulk orders are quoted separately, so send the size and quantity you need. In practice, a lateral line needs one cap per run, plus spares for maintenance.

HDPE end cap fittings in three sizes, green compression bodies with black caps and clinching rings
Compression end stops shown open: the cap, clinching ring and body that grip the pipe without threads.

 

How an HDPE End Cap Seals the Pipe

The fitting has five parts: a cap, an O-ring, a clinching ring, a blocking bush and the body. First, the pipe slides into the body. Then the cap nut compresses the clinching ring onto the pipe wall. As a result, the joint grips without threads.

Because there are no external or internal threads, the same cap fits HDPE or PPR pipe. This differs from female and male adapters, which rely on threaded joints. The O-ring seals against the pipe outside surface.

The blocking bush stops the pipe sliding too far into the body. As a result, the clinching ring lands on the correct seat every time. This is what makes the joint repeatable after reuse.

The grip also flexes with the pipe. Therefore the joint withstands pipeline expansion and contraction and other stresses, instead of loosening as temperatures change.

 

HDPE End Cap Pressure Rating (PN16 to PN25)

Compression end caps carry a pressure nominal rating, PN16 to PN25. The PN number is the working pressure the material tolerates. Therefore a larger PN means a stronger fitting.

Most caps are moulded from high-density polyethylene. This resists corrosion, which can otherwise compromise water quality in irrigation. Typically the nominal diameter, the inside diameter, sets the size you choose. Common plastic compression sizes run 20 mm up to 91 mm; this listing stocks 20 mm up to 63 mm.

 

Where to Use an HDPE End Cap

The cap closes any line that must stop at a dead end. Common uses include the following.

  • Terminating irrigation laterals in drip and sprinkler systems.
  • Closing ends of temporary or seasonal farm lines.
  • Domestic water supply networks, as an end stop.
  • Quick shut-off during pipeline extensions or maintenance.

Also, caps let you isolate a section while you extend the rest of the network. Instead of cutting and rejoining pipe, you simply cap the open end.

In seasonal systems, caps protect open ends against dirt and insects during the off months. Therefore the line stays clean when you reopen it next season.

 

Fitting an HDPE End Cap Correctly

First, cut the pipe square and remove burrs. Then slide the cap nut and clinching ring onto the pipe. Next, push the pipe fully into the body until it seats. Finally, tighten the cap nut by hand, then a quarter turn with a spanner.

Check the O-ring sits flat before tightening. A twisted O-ring leaks under pressure. However, do not overtighten, because the polymer nut can crack. The joint needs no glue or thread tape.

If a joint weeps, undo the nut and reseat the pipe. Also check the clinching ring for cracks, because a split ring will not grip. Similarly, a flattened O-ring must be replaced before the line is pressurised again.

 

HDPE End Cap Frequently Asked Questions

Does an HDPE end cap need threads?

No. It is a compression fitting, so it grips the plain pipe end. Therefore it suits HDPE and PPR pipe alike.

What pressure can it hold?

PN16 to PN25, depending on the size and class. The PN number is the working pressure rating.

Which size do I choose?

Match the cap to the pipe outside diameter: 63 mm, 50 mm, 40 mm, 32 mm, 25 mm or 20 mm. The nominal size is marked on the body.

Can I reuse the cap?

Yes. Undo the nut, slide the cap off and refit it on a new pipe end. Replace the O-ring if it is cut or flattened.

Does it fit PPR pipe?

Yes, provided the outside diameter matches. The threadless compression grip works on both HDPE and PPR.

Is it cheaper than a threaded cap?

Compression caps need no threading or glue, so installation is faster. Prices start at KSh 100 on sale.

 

Order HDPE End Cap in Kenya

Eunidrip Irrigation Systems supplies HDPE end cap fittings in all six sizes, with countrywide delivery. Contact us by phone, WhatsApp or email for a quotation. We supply single fittings and bulk orders for contractors.

Finally, pair the cap with the right pipe and fittings. Our HDPE elbows and couplings listings complete the line, and the HDPE pipe fittings guide covers the whole range.

Additional information

Weight N/A
END CUP sizes

1 ½ " – 50mm, 1 ¼" – 40mm, 1" – 32mm, ½ " – 20mm, 2" – 63mm, ¾" – 25mm

Call Us WhatsApp